Buying guide

Furniture materials, finishes & hardware

Two sofas can look identical in a photograph and behave very differently after a year. One has a hardwood frame with tight joints and a resilient cushion; the other has a stapled...

Explore the guide
Furniture materials, finishes & hardware

Two sofas can look identical in a photograph and behave very differently after a year. One has a hardwood frame with tight joints and a resilient cushion; the other has a stapled particleboard carcass and foam that flattens. Material and construction decide how a piece wears and what it needs in cleaning. This guide covers the four material groups, the details worth checking in each, and the trade-offs.

Brown square dining table with two chairs
Timber grain and joints at the table edge

Solid timber

What does solid timber mean once it is in your room?

Solid timber means the wood itself rather than a veneer, so the grain runs through a leg or top and the piece can usually be sanded and refinished. Check that boards are straight, that joins are tight and that any filler is small and dry. Look at how the legs meet the rails: a mortise-and-tenon joint or a bolted corner block is easier to trust than staples or screws into end grain. Timber moves with humidity, so a top may show a fine gap in dry weather.

The finish decides how much work the timber will need. A lacquer film resists water and wipes clean but can chip at an edge and is harder to spot repair. An oil or wax finish feels closer to the grain and can be refreshed at home, though it needs re-oiling and marks more easily from heat and liquid. Ask what the maker recommends for cleaning, and use coasters under hot cups. Direct sun can shift timber tones, so rotate pieces that sit in a window.

  • Check joints at the legs and rails, not just the tabletop.
  • Ask which finish is used and how it is repaired.

Shop kitchen and dining furniture Care for timber and veneer

Compact study desk with fabric drawers for a home office
A laminate desktop with sealed edges

Veneer and laminate

Where do veneer and laminate make more sense than solid wood?

Veneer is a thin slice of real timber glued to a stable board such as plywood, MDF or particleboard. Laminate is a printed and resin bonded surface, often on the same boards. Both give a flatter, more consistent panel than solid timber, weigh less and move less with the seasons. The quality sits in the substrate and the edges. Look for a board that feels dense rather than hollow, edge banding that is tight and smooth, and sealed edges around any cut-out, because water reaches the core through an open edge.

The trade-offs are repairability and heat. A veneered top can be sanded lightly, but only once or twice, and a deep chip is difficult to disguise. Laminate resists daily wear well but a hot pan or a standing spill can lift or stain the surface, and a knife mark is difficult to sand out. Keep both away from steam and wipe spills promptly rather than letting water sit along a seam. If a cabinet will hold heavy books, check the stated shelf load and support long spans.

  • Look for tight, smooth edge banding on shelves and doors.
  • Wipe spills along seams before water reaches the core.

Shop office desks and furniture Compare room layouts

Grey outdoor hammock chair with armrests
Metal frames need even coating and sound welds

Metal and glass

How do metal and glass frames age?

Metal frames are usually steel or aluminium, and the difference matters outdoors. Steel is strong and rigid but can rust once the coating is breached, so check welds, inside corners and any scratch. Aluminium is lighter and does not rust, though it can still corrode in coastal air if the finish is thin. Powder coating should be even, with no thin patches around joints or bolt holes. On glass, look for a finished edge, a sensible thickness for the span and a frame that supports the panel along its length.

The practical trade-offs are weight and upkeep. Glass is heavy for its size, so a large top needs two people to move and a frame designed for that load. It shows fingerprints quickly, and a hard knock at an edge is more likely to damage it than one in the middle. Metal conducts heat and cold, which matters where wrists rest on a desk. Fit felt pads under metal legs to protect timber and tile, and check that wall brackets are rated for the load.

  • Check welds and the inside of legs for rust or thin coating.
  • Use felt pads under metal legs on timber and tile.

Shop outdoor furniture Check fixings and wall support

Black LED TV cabinet and entertainment unit with power outlets
Seams, cushions and fabric under daily use

Upholstery and leather

Upholstery has to suit the household, not only the room.

Under the fabric there is a frame, webbing or springs and foam, and that is where comfort comes from. Ask about foam density and whether the covers are removable, because a soft low density seat can flatten sooner. Look at the seams: a straight seam with even stitching and a generous seam allowance lasts better than a tight one that pulls. A tight weave handles pets and daily vacuuming better than a loose one, and a performance finish can help with spills, though it still needs prompt cleaning.

Leather is measured less by thickness than by the finish on top. An aniline or semi-aniline hide keeps the natural surface and develops a patina, but it marks and fades more readily. A protected or pigmented leather has a coating that resists spills and is easier to wipe, at the cost of some natural feel. Both dislike sharp claws, direct sun and heat, and both need a gentle wipe rather than a soaked cloth. Check the care code and follow it, since the wrong product can dull the finish.

  • Ask for a swatch and view it in your own room light.
  • Check foam density and whether covers are removable.

Shop living room furniture Care for upholstery and leather

Popular pieces worth comparing

These are among the current best-selling Furniture pieces. Check the dimensions, finish and care notes on each listing before ordering.

Material choices are rarely about one being better than another. Solid timber suits pieces that will be sanded and kept for years, veneer and laminate suit long flat panels and tighter budgets, metal and glass suit desks and outdoor settings that need to shed water, and upholstery should be chosen around the people and pets who use it. Read the finish and care notes before you order.

Shop all furniture